Linux version 2.6.8-1-386 (dilinger@toaster.hq.voxel.net) (gcc version 3.3.4 (Debian 1:3.3.4-13)) #1 Thu Oct 7 02:21:16 EDT 2004
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001df40000 (usable)
 BIOS-e820: 000000001df40000 - 000000001df50000 (ACPI data)
 BIOS-e820: 000000001df50000 - 000000001e000000 (ACPI NVS)
 BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved)
479MB LOWMEM available.
On node 0 totalpages: 122688
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 118592 pages, LIFO batch:16
  HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 ACPIAM                                    ) @ 0x000faba0
ACPI: RSDT (v001 A M I  OEMRSDT  0x05000418 MSFT 0x00000097) @ 0x1df40000
ACPI: FADT (v001 A M I  OEMFACP  0x05000418 MSFT 0x00000097) @ 0x1df40200
ACPI: ECDT (v001 A M I  OEMECDT  0x05000418 MSFT 0x00000097) @ 0x1df40360
ACPI: OEMB (v001 A M I  OEMBIOS  0x05000418 MSFT 0x00000097) @ 0x1df50040
ACPI: SSDT (v001    AMI   CPU1PM 0x00000001 INTL 0x20030522) @ 0x1df45c70
ACPI: DSDT (v001  A0009 A0009000 0x00000000 INTL 0x20030522) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
Built 1 zonelists
Kernel command line: root=/dev/hda1 ro 
Found and enabled local APIC!
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 1600.582 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 478924k/490752k available (1329k kernel code, 11084k reserved, 723k data, 204k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3178.49 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: afe9fbbf 00000000 00000000 00000000
CPU: After vendor identify, caps:  afe9fbbf 00000000 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps:        afe9fbbf 00000000 00000000 00000040
CPU: Intel(R) Pentium(R) M processor 1.60GHz stepping 06
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1599.0831 MHz.
..... host bus clock speed is 99.0989 MHz.
checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
Freeing initrd memory: 4316k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: IRQ9 SCI: Edge set to Level Trigger.
ACPI: Found ECDT
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: Embedded Controller [EC0] (gpe 6)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 *4 5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 *10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f5e40
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x69fa, dseg 0xf0000
PNPBIOS fault.. attempting recovery.
PnPBIOS: Warning! Your PnP BIOS caused a fatal error. Attempting to continue
PnPBIOS: You may need to reboot with the "nobiospnp" option to operate stably
PnPBIOS: Check with your vendor for an updated BIOS
PnPBIOS: get_dev_node: unexpected status 0x28
PnPBIOS: 5 nodes reported by PnP BIOS; 5 recorded by driver
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:13.0[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:00:13.1[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:00:13.2[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:14.1[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
ACPI: PCI interrupt 0000:00:14.5[B] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt 0000:00:14.6[B] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt 0000:01:05.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt 0000:02:05.1[B] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 4
ACPI: PCI interrupt 0000:02:05.2[C] -> GSI 4 (level, low) -> IRQ 4
ACPI: PCI interrupt 0000:02:06.0[A] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt 0000:02:07.0[A] -> GSI 4 (level, low) -> IRQ 4
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ACPI: PCI interrupt 0000:00:14.6[B] -> GSI 5 (level, low) -> IRQ 5
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
EISA: Probing bus 0 at eisa0
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S3 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4316 blocks [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 204k freed
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ATIIXP: IDE controller at PCI slot 0000:00:14.1
ACPI: PCI interrupt 0000:00:14.1[A] -> GSI 11 (level, low) -> IRQ 11
ATIIXP: chipset revision 0
ATIIXP: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:pio
hda: IC25N040ATMR04-0, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 1024KiB
hda: 78140160 sectors (40007 MB) w/1740KiB Cache, CHS=16383/255/63, UDMA(100)
 /dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4
hdc: MATSHITAUJ-831D, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 1951888k swap on /dev/hda3.  Priority:-1 extents:1
EXT3 FS on hda1, internal journal
Real Time Clock Driver v1.12
hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ieee1394: Initialized config rom entry `ip1394'
SCSI subsystem initialized
sbp2: $Rev: 1219 $ Ben Collins <bcollins@debian.org>
Capability LSM initialized
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Linux Kernel Card Services
  options:  [pci] [cardbus] [pm]
ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 5 (level, low) -> IRQ 5
Yenta: CardBus bridge found at 0000:02:05.0 [1043:1904]
Yenta: ISA IRQ mask 0x0088, PCI irq 5
Socket status: 30000006
PCI: Enabling device 0000:02:05.1 (0000 -> 0002)
ACPI: PCI interrupt 0000:02:05.1[B] -> GSI 10 (level, low) -> IRQ 10
Yenta: CardBus bridge found at 0000:02:05.1 [1043:1904]
Yenta: ISA IRQ mask 0x0088, PCI irq 10
Socket status: 30000006
ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org>
ACPI: PCI interrupt 0000:02:05.2[C] -> GSI 4 (level, low) -> IRQ 4
ohci1394: fw-host0: Get PHY Reg timeout [0x00000000/0x00000000/100]
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[4]  MMIO=[fb300000-fb3007ff]  Max Packet=[2048]
ohci1394: fw-host0: Get PHY Reg timeout [0x00000000/0x00000000/100]
8139too Fast Ethernet driver 0.9.27
ACPI: PCI interrupt 0000:02:06.0[A] -> GSI 5 (level, low) -> IRQ 5
eth0: RealTek RTL8139 at 0xe800, 00:11:2f:f8:bb:b2, IRQ 5
eth0:  Identified 8139 chip type 'RTL-8101'
eth0: link down
ohci1394: fw-host0: Get PHY Reg timeout [0x00000000/0x00000000/100]
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected Ati IGP9100/M chipset
agpgart: Maximum main memory to use for agp memory: 409M
agpgart: AGP aperture is 32M @ 0xfc000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ACPI: PCI interrupt 0000:00:13.0[A] -> GSI 10 (level, low) -> IRQ 10
ohci_hcd 0000:00:13.0: PCI device 1002:4347 (ATI Technologies Inc)
ohci_hcd 0000:00:13.0: irq 10, pci mem dea6d000
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ACPI: PCI interrupt 0000:00:13.1[A] -> GSI 10 (level, low) -> IRQ 10
ohci_hcd 0000:00:13.1: PCI device 1002:4348 (ATI Technologies Inc)
ohci_hcd 0000:00:13.1: irq 10, pci mem dea6f000
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
usb 1-1: new low speed USB device using address 2
usbcore: registered new driver hiddev
input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:13.0-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
ACPI: PCI interrupt 0000:00:13.2[A] -> GSI 10 (level, low) -> IRQ 10
ehci_hcd 0000:00:13.2: PCI device 1002:4345 (ATI Technologies Inc)
ehci_hcd 0000:00:13.2: irq 10, pci mem dea71000
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:13.2: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
usb 1-1: USB disconnect, address 2
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 6 ports detected
ohci_hcd 0000:00:13.0: wakeup
usb 1-1: new low speed USB device using address 3
input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:13.0-1
ACPI: PCI interrupt 0000:00:14.5[B] -> GSI 5 (level, low) -> IRQ 5
ATI IXP AC97 controller: probe of 0000:00:14.5 failed with error -13
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
cs: IO port probe 0x0100-0x04ff: excluding 0x228-0x22f 0x378-0x37f 0x408-0x40f 0x4d0-0x4d7
cs: IO port probe 0x0800-0x08ff: excluding 0x800-0x817 0x820-0x827 0x830-0x837 0x850-0x857
cs: IO port probe 0x0c00-0x0cff: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcd7
cs: IO port probe 0x0a00-0x0aff: clean.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02c95a0(lo)
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.